Inspection reports & case studies

What we check, how we document it, and four orders where an inspection changed the outcome. Client names are withheld; every case is published with permission.

Inside a report

One document, no room for opinion

Every inspection ends with the same structure. You do not need to trust a summary — you can count the defects yourself.

  • Order and factory details, inspector name, date and time on site
  • Lot size, sample size, AQL level, accept / reject numbers
  • Critical, major and minor defects with photo references
  • Measurement table against the approved sample
  • Packaging, labelling and carton test results
  • Verdict, corrective actions and re-inspection date
Pre-shipment inspection report CS-2418-01
Product
Bluetooth speaker, model S12
Order quantity
3,000 pcs / 250 cartons
Sample size (AQL 2.5)
125 pcs
Major defects found
6 pcs (limit 7)
Minor defects found
9 pcs (limit 10)
Result
Pass with rework
Evidence
52 photos · 4 videos

Illustrative report. Your report is delivered as a signed PDF with the photo set.

Sampling standard

How many units we check, and when we reject

We sample to ISO 2859-1, general inspection level II, AQL 2.5 for major and 4.0 for minor defects. Critical defects — safety, function, legal labelling — are zero tolerance.

Lot size (units) Sample size Accept Reject Typical inspection time
151 – 28032232–3 hours
281 – 50050342–3 hours
501 – 1,20080563–5 hours
1,201 – 3,200125783–5 hours
3,201 – 10,00020010111 full day
10,001 – 35,00031514151–2 days

For orders above 35,000 units or multi-SKU lots, we quote a tailored sampling plan and inspector-days before the visit.

Case studies

Four shipments that were fixed before they left China

Different categories, same method: sample, measure, document, then decide with evidence.

Inspector measuring an electronic enclosure with calipers
Consumer electronics

Bluetooth speakers — 3,000 units, Shenzhen

A first order from a new factory. Inspection found 6 units with battery swelling after a 2-hour charge test and 14 with misaligned rubber feet. The factory blamed the courier; the photos did not.

We held the balance, required a battery batch change and full re-test, then re-inspected the reworked lot.

3,000units re-checked
0defects on arrival
9 daysdelay, not a recall
Cartons stacked in an export warehouse awaiting inspection
Furniture

Solid oak dining chairs — 240 units, Foshan

Moisture content measured 13.8% against a 10% maximum — the chairs would have cracked in a heated European home. Finish thickness was also below spec on 40 seats.

Wood was re-dried and refinished before packing; we re-inspected moisture on every carton and supervised the container loading.

240chairs reworked
$18kretail value protected
0cracks reported
Sourcing team reviewing product samples and inspection documents
Textiles

Organic cotton hoodies — 5,000 units, Nantong

Colour fastness failed a wash test, and size labels were swapped on two sizes. For a marketplace seller, either issue means returns and a suspended listing.

300 units were remade, all labels reprinted and re-sewn, and a 10-piece wash test was repeated before release.

5,000units relabelled
1.2%return rate after launch
0listing complaints
Container terminal where inspected cargo is loaded for export
Housewares

Ceramic mugs — 12,000 units, Chaozhou

Rims were chipping at 8% because the factory had switched to a thinner inner carton to save cost. Breakage would have been discovered only by the end customer.

We rejected the packaging, specified a 5-layer carton with moulded pulp inserts, and ran a drop test on 3 cartons from 80 cm.

12,000units repacked
0.4%breakage on arrival
$3.1kclaims avoided

"The report told me the factory had changed the carton spec without telling anyone. That single page saved a whole container of returns."

Lena N.Homeware brand · Netherlands

Want a report like this on your next order?

Send the product and the quantity. We will tell you the sampling plan, the inspector-days and the fee before anyone visits the factory.